Sürdürülebilir Kalkınma Amaçları
Yazarlar
Yayınlar
- MakaleYalnız künye2018Bearing capacity and slope stability assessment of rock masses at the Subasi viaduct site, NE, Turkey
Kaya, Ayberk; Bulut, Fikri; Dağ, Serhat
This study investigates the bearing capacity of rock masses and stability of slopes at the Subasi viaduct site which is a part of the improvement project of the Artvin–Hopa government highway between KM 6 + 500 and 13 + 787 in NE Turkey. The geotechnical studies were performed in three stages. Firstly, the bearing capacity of moderately weathered andesitic tuff was evaluated using the empirical equations. Secondly, the major principal stress and vertical displacement due to the viaduct and traffic loadings at the level of foundations were determined by the finite element method (FEM). The vertical displacement value and comparison of bearing capacity and major principal stress show that any problem is not expected at the viaduct site in terms of the bearing capacity. Finally, the stability of slopes at the viaduct site was investigated using kinematic, limit equilibrium, and finite element method-based shear strength reduction analyses methods. It was concluded that no discontinuity controlled failures at the slopes are expected. However, a circular failure is possible to occur at the face slope excavated in highly weathered andesitic tuff. After support application, the long-term stabilization of face slope has been achieved. Consequently, it is suggested that the empirical, analytical, and numerical methods should be combined for a more reliable construction design.
- MakaleAçık Erişim2017The importance of amount of settlement in determining the bearing capacity of soils
Alemdaǧ, Selçuk; Cinoǧlu, Aslihan; Gacener, Elif
In this study, it is aimed to determine safe bearing capacity of soils, which are out cropped around Tamzi and Akcakale villages located in Gumushane, providing allowable settlement conditions for an optimum foundation design. To define the geotechnical properties of soils, three trenches were dug and two seismic refraction with two Multichannel Spectral Analysis of Surface Waves (MASW) were carried out in each research area. Sieve analyses, shear box tests, triaxial compression tests were carried out on disturbed and undisturbed samples taken from the trenches. Seismic velocities of the soils are determined by seismic refraction and MASW methods. While determining the safe bearing capacity; the equations proposed by Terzaghi, Meyerhof, Kurtuluş, Tezcan and Özdemir, Türker, Keçeli were used and the obtained safe bearing capacity values were compared to each other. After, the soils were modeled numerically by using finite elements method and safe bearing capacities providing allowable settlement conditions were determined. According to the results, safe bearing capacity values obtained from empirical equations are not satisfactory to have an optimum foundation design. For the optimum foundation design, safe bearing capacity should be accepted as 190 kN/m2 for clayey soil (CL) and 485 kN/m2 for the clayey sand (SC).
- MakaleYalnız künye2015Assessment of bearing capacity and permeability of foundation rocks at the Gumustas Waste Dam Site (NE Turkey) using empirical and numerical analysis
Alemdag, Selcuk
In this study, the bearing capacity and permeability of andesite and andesitic breccia rock masses, forming the basement for Gumustas waste dam, planned as a rock fill housing, were evaluated using various empirical equations and numerical analysis. The total stress constituting over the basement caused through ore waste building up in the body of dam and reservoir was determined by a finite element method. Then, this stress was compared with bearing capacities calculated for the rock masses. The permeability of rock masses in dam site and the lake were appraised with pressure water test experiments (Lugeon method), performed within opened bore holes and finite element method (seepage analysis). Since chemicals seeping from waste dams into the ground water are of vital importance for human health and the environment, the dam body must be made completely impervious using upstream slope and reservoir geosynthetics.