Sürdürülebilir Kalkınma Amaçları
Yayınlar
- MakaleYalnız künye2014Simultaneous separation and preconcentration of Ni(II) and Cu(II) ions by coprecipitation without any carrier element in some food and water samples
Duran, Celal; Tumay, Sureyya O.; Ozdes, Duygu; Serencam, Huseyin; Bektas, Hakan
A simple and highly sensitive separation and preconcentration procedure, which has minimal impact on the environment, has been developed. The procedure is based on the carrier element-free coprecipitation of Ni(II) and Cu(II) ions by using 2-{4-[2-(1H-Indol-3-yl)ethyl]-3-(4-chlorobenzyl)-5-oxo-4,5-dihydro-1H-1,2,4-triazol-1-yl}-N′-(pyrrol-2-ylmethyliden)acetohydrazide (ICOTPA), as an organic coprecipitant. The levels of analyte ions were determined by flame atomic absorption spectrometry. The detection limits for Ni(II) and Cu(II) ions were found to be 0.27 and 0.58 μg L-1, respectively, and the relative standard deviations for the analyte ions were lower than 4.0%. Spike tests and certified reference material analyses were performed to validate the method. The method was successfully applied for the determination of Ni(II) and Cu(II) ions levels in sea and stream water as liquid samples and red lentil and rice as solid samples.
- MakaleAçık Erişim2013Solid phase extraction of Cd(ii) and pb(ii) ions by a new carbothioamide derivative
Ozdes, Duygu; Duran, Celal; Bayrak, Hacer; Serencam, Huseyin; Basri Senturk, Hasan
An effective, simple, low cost and accurate sorption-spectrophotometric platform for the extractions and subsequent quantifications of Cd(II) and Pb(II) ions in food and environmental samples has been described in this dissertation. The separation and preconcentration of the analyte ions were accomplished by solid phase extraction method based on the adsorption of their N-(4-methylphenyl)-2-{[(4-phenyl-5-pyridin-4-yl-4H-1,2,4-triazol-3-yl)thio] acetyl} hydrazinecarbothioamide (MFPTAHK) complex on Amberlite XAD-8 resin in a mini column. The developed method was systematically investigated in different set of experimental parameters that influence the separation and preconcentration of Cd(II) and Pb(II) ions. The precision of the method was determined by reproducibility studies and expressed as relative standard deviations (RSD %) which were less than 4% for both analyte ions. The limits of detections (LODs) for Cd(II) and Pb(II) ions based on the three times the standard deviation of the blanks (N:10) were found to be 0. 31 ?g L-1 and 0. 86 ?g L-1, respectively. The developed SPE procedure was utilized for the simultaneous extraction and determinations of Cd(II) and Pb(II) ions levels in rice, cracked wheat and red lentil as food samples and various water samples.
- MakaleYalnız künye2013Application of carrier element free coprecipitation (CEFC) method for determination of Co(II), Cu(II) and Ni(II) ions in food and water samples
Serencam, Huseyin; Duran, Celal; Ozdes, Duygu; Bektas, Hakan
A simple and highly sensitive separation and preconcentration procedure, which has minimal impact on the environment, has been developed. The procedure is based on the carrier element free coprecipitation (CEFC) of Co(II), Cu(II), and Ni(II) ions by using 2-{4-[2-(1H-indol-3-yl)ethyl]-3-(4-methylbenzyl)-5-oxo- 4,5-dihydro-1H-1,2,4-triazol- 1-yl}-N'-(pyridin-2-yl methylidene)acetohydrazide (IMOTPA), as an organic coprecipitant. The levels of analyte ions were determined by flame atomic absorption spectrometry (FAAS). The detection limits for Co(II), Cu(II) and Ni(II) ions were found to be 0.40, 0.16 and 0.17 μg L-1, respectively, and the relative standard deviations for the analyte ions were lower than 3.0%. Spike tests and certified reference material analyses were performed to validate the method. The method was successfully applied for the determination of Co(II), Cu(II) and Ni(II) ions levels in sea and stream water as liquid samples and red pepper, black pepper, and peppermint as solid samples.
- MakaleYalnız künye2013Separation and pre-concentration of palladium(II) from environmental and industrial samples by formation of a derivative of 1,2,4-triazole complex on Amberlite XAD-2010 resin
Serencam, Huseyin; Bulut, Volkan Numan; Tufekci, Mehmet; Gundogdu, Ali; Duran, Celal; Hamza, Sibel; Soylak, Mustafa
A simple separation/pre-concentration method was developed for extraction of Pd(II) in various environmental samples, based on its adsorption of 4-phenyl-5-{[(4-phenyl-5-pyridin-4-yl-4H-1,2,4-triazole-3-yl)thio]methyl}-4H-1,2,4-triazole-3-thyol (PPTTMET) complex on Amberlite XAD-2010 resin in a mini column. The ligand has high affinity for Pd(II) among many other metals that are taken into consideration. The flame atomic absorption spectrometry is employed to determine the concentration of Pd(II). The optimum working conditions which were determined are as follows: 0.05 mol L-1 HNO3 as working medium, 1.0 mol L-1 HCI in acetone as elution solvent, 0.75 mg of PPTTMET amount and 750 mL of sample volume. The system was independent from the flow rates between 3.1 and 23.1 mL min-1. The Pd(II) adsorption capacity of Amberlite XAD-2010 resin was found to be 12.8 mg g-1 and the enrichment factor was calculated as 375. The method was successfully applied for the determination of Pd(II) in motorway dust samples, anodic sludge, gold ore, industrial electronic waste materials and various water samples.
- MakaleYalnız künye2013Biosorption properties of Morus alba L. for Cd (II) ions removal from aqueous solutions
Serencam, Huseyin; Ozdes, Duygu; Duran, Celal; Tufekci, Mehmet
The abundantly available industrial waste product Morus alba L. pomace (MAP) is one of the cost-effective biosorbent for removal of metal ions from aqueous solutions. Hence, in the present study, we aimed to test the ability of MAP to remove Cd(II) ions through batch biosorption process. Firstly, MAP was characterized using several techniques, and then the influence of various experimental parameters such as initial pH of the aqueous solution, initial Cd(II) concentration, contact time, MAP concentration, and temperature were evaluated upon the biosorption process. It was found that the maximum uptake of Cd(II) ions occurred at initial pH 6.0 and optimum contact time was observed as 60 min. Cd(II) ions adsorption on MAP analyzed by the Langmuir and Freundlich isotherm models and the maximum monolayer biosorption capacity of MAP was found to be 21.69 mg g-1 by using the Langmuir isotherm model. The pseudo-first-order, pseudo-second-order, Elovich, and intraparticle diffusion models were employed to describe the biosorption kinetics. In order to investigate the thermodynamic properties of the biosorption process, the changes in the Gibbs free energy (â̂†G), enthalpy (â̂†H), and entropy (â̂†S) were also evaluated and it has been concluded that the process was feasible, spontaneous, and endothermic in the temperature range of 5-40 C.
- MakaleAçık Erişim2013Selective Separation, Preconcentration, and Determination of Au (III) Ions in Environmental Samples by Coprecipitation With a 1,2,4-Triazole Derivative
Ozdes, Duygu; Duran, Celal; Serencam, Huseyin; Şahin, Deniz
An effective, simple, lowcost, and accurate separation and preconcentration procedure which has minimal impact on the environment has been developed. It is based on the carrier element-free coprecipitation (CEFC) of Au(III)ions using N-benzyl-2-{[3-methyl-4-(2morpholine-4-ylethyl)-5-oxo-4,5-dihydro-1H-1,2, 4-triazole-1-yl] acetyl)hydrazinecarboxamide (BODAH) as an organic coprecipitant. Determination of the Au(IH) ion levels was performed by flame atomic absorption spectrometry (FAAS). The developed method provided a detection limit of 0.36 μg L-1 and the relative standard deviation for Au(III)ions was found to be 5.1%. Spike tests and certified reference material analyses were performed to validate the method. The developed method was systematically investigated in different sets of experimental parameters that influence the quantitative recovery of the Au(III)ions. Based on these investigations, the optimum conditions for the determination of Au(III) ions at trace levels were established. The coprecipitation method was applied to anodic slime, gold ore, soil, and water samples to determine their Au(III)levels.
- MakaleAçık Erişim2013Separation and preconcentration of copper in environmental samples on amberlite XAD-8 resin after complexation with a carbothioamide derivative
Elvan, Hamide; Ozdes, Duygu; Duran, Celal; Sahin, Deniz; Tufekci, Mehmet; Bahadir, Zekeriyya
A new solid phase extraction (SPE) method has been developed for the selective separation and preconcentration of Cu (II) ions in food and water samples prior to its flame atomic absorption spectrometry determination. The method is based on the adsorption of the Cu(II)-2-{[4-Amino-3-(4-methylphenyl-5- oxo-4,5-dihydro-1H-1,2,4-triazol-1-yl]acetyl}-N-phenyl hydrazinecarbothioamide complex on Amberlite XAD-8 resin. The metal complex retained on the resin was eluted with 7.5 mL of 2.0 mol L-1 HCl in acetone. The optimum conditions for the SPE of Cu(II) ions were investigated, and the method was subsequently applied to sea water, stream water, rice, tea, and tobacco samples for the determination of Cu(II) levels.
- MakaleAçık Erişim2013Development of a new solid phase extraction procedure for selective separation and enrichment of Au(III) ions in environmental samples
Elvan, Hamide; Ozdes, Duygu; Duran, Celal; Bulut, V. Numan; Gümrükçüoglu, Nurhan; Soylak, Mustafa
A highly sensitive, selective and low cost solid phase extraction (SPE) procedure was developed for separation and enrichment of Au(III) ions in environmental samples prior to its flame atomic absorption spectrometric detection. Au(III)-2-pyridin-5-(4-tolyl)-1,3,4-oxadiazole (PYTOX) complex was adsorbed quantitatively on Amberlite XAD-4 resin in 0.5 mol L-1 HNO3 condition and the elution was carried out with 7.5 mL of 1.0 mol L-1 HCl in acetone. Some analytical parameters, affect the recoveries of Au(III) ions, such as HNO3 concentration of sample solution, amount of PYTOX, type, concentration and volume of eluent, sample volume and concomitants were examined. Adopting optimized experimental conditions, the limit of detection for Au(III) ions was 1.03 μg L-1 with preconcentration factor of 50 and a relative standard deviation (RSD) of 3.7%. The determination of Au(III) ions in anodic slime, gold ore, soil and sea and stream waters was performed after checking the accuracy of the method by addition-recovery tests.
- MakaleYalnız künye2013Determination of Pb(II), Zn(II), Cd(II), and Co(II) ions by flame atomic absorption spectrometry in food and water samples after preconcentration by coprecipitation with Mo(VI)-diethyldithiocarbamate
Tufekci, Mehmet; Bulut, Volkan Numan; Elvan, Hamide; Ozdes, Duygu; Soylak, Mustafa; Duran, Celal
A new, simple, and rapid separation and preconcentration procedure, for determination of Pb(II), Cd(II), Zn(II), and Co(II) ions in environmental real samples, has been developed. The method is based on the combination of coprecipitation of analyte ions by the aid of the Mo(VI)-diethyldithiocarbamate- (Mo(VI)-DDTC) precipitate and flame atomic absorption spectrometric determinations. The effects of experimental conditions like pH of the aqueous solution, amounts of DDTC and Mo(VI), standing time, centrifugation rate and time, sample volume, etc. and also the influences of some foreign ions were investigated in detail on the quantitative recoveries of the analyte ions. The preconcentration factors were found to be 150 for Pb(II), Zn(II) and Co(II), and 200 for Cd(II) ions. The detection limits were in the range of 0.1-2.2 μg L-1 while the relative standard deviations were found to be lower than 5 % for the studied analyte ions. The accuracy of the method was checked by spiked/recovery tests and the analysis of certified reference material (CRM TMDW-500 Drinking Water). The procedure was successfully applied to seawater and stream water as liquid samples and baby food and dried eggplant as solid samples in order to determine the levels of Pb(II), Cd(II), Zn(II), and Co(II) ions.
- MakaleYalnız künye2013Physicochemical characteristics of a novel activated carbon produced from tea industry waste
Gundogdu, Ali; Duran, Celal; Senturk, H. Basri; Soylak, Mustafa; Imamoglu, Mustafa; Onal, Yunus
Tonnes of waste are generated during tea production in Turkey, one of the black tea producing countries in the world. These wastes are not used for any purposes throughout industrial sector. The objective of this study is to bring in economic value to waste materials by producing activated carbons from wastes of a tea plant and to characterize their physicochemical properties. Three types of activated carbons were produced by chemical activation using zinc chloride from tea industry wastes (TIW). Mesoporous structure and surface area rise as the ratio of ZnCl2/TIW increases. When the ratios of ZnCl2/TIW were selected as 1/2:1, 1:1, and 2:1, mesoporous activated carbons are found in the percentages of 10.9%, 39.9% and 77.7% with BET surface areas of 706, 1066 and 1141 m(2) g(-1), respectively. The resultant activated carbons were characterized by analyses of proximate-ultimate, FT-IR, SEM, TGA, methylene blue-iodine numbers, and surface functional groups. (C) 2013 Elsevier B.V. All rights reserved.
- MakaleYalnız künye2013Cadmium and nickel determinations in some food and water samples by the combination of carrier element-free coprecipitation and flame atomic absorption spectrometry
Bahadir, Zekeriyya; Ozdes, Duygu; Bulut, Volkan Numan; Duran, Celal; Elvan, Hamide; Bektas, Hakan; Soylak, Mustafa
A procedure for separation and enrichment of Cd(II) and Ni(II) ions based upon carrier element-free coprecipitation by using an organic coprecipitant, 2-{4-[2-(1H-Indol-3-yl)ethyl]-3-(4-methylbenzyl)-5-oxo-4,5-dihydro-1H-1,2,4-triazol-1-yl}-N-(3-fluoro-phenylmethyliden) acetohydrazide, prior to their flame atomic absorption spectrometric detections has been developed. The effects of varied experimental conditions on the performance of the developed method such as pH, sample volume, amount of coprecipitating agent, etc. were evaluated in detail on the recovery of analyte ions, and the influences of some anions and cations were investigated. The limits of detection for Cd(II) and Ni(II) ions based on three times the standard deviation of the blanks (N: 10) were obtained as 0.70 g L-1 and 1.21 g L-1, respectively. The accuracy of the method was tested by analyzing a certified reference material and by spike tests. The method was applied to determine the levels of cadmium and nickel in stream and sea water, rice, red lentil, and wheat samples.
- MakaleAçık Erişim2012Dehydrated hazelnut husk carbon: A novel sorbent for removal of Ni(II) ions from aqueous solution
Sivrikaya, Sezen; Albayrak, Sinem; Imamoglu, Mustafa; Gundogdu, Ali; Duran, Celal; Yildiz, Hulya
The present study has been performed to examine the adsorption ability of novel sorbent dehydrated hazelnut husk carbon (DHHC) towards Ni(II) ions from aqueous solution using the batch adsorption technique. The effective factors such as initial pH of the aqueous solution, contact time, initial Ni(II) concentration, adsorbent dosage, and temperature were investigated. The studies were also conducted to understand the effect of some co-existing ions which may be present in aqueous solutions. DHHC showed good adsorption potential for Ni(II) ions. The optimum initial pH value was selected as 5.0. The experimental data fitted well to the Langmuir adsorption isotherm model. Among the kinetic models tested for the adsorption of Ni(II), the pseudo-second-order model showed a good fit of the kinetic data. The thermodynamic parameters including the Gibbs free energy (ΔG), enthalpy (ΔH), and entropy (ΔS) changes indicated that the adsorption of Ni(II) ions onto DHHC was feasible, spontaneous, and exothermic in the temperature range of 25-55°C. The results of this study showed the effectiveness and feasibility of DHHC for the removal of Ni(II) ions from aqueous solution.
- BildiriYalnız künye2012Acetohydrazide derivative for selective separation and preconcentration of Cu(II) ions by coprecipitation method without using a carrier element
Ozdes, Duygu; Duran, Celal; Bektaş, Hakan; Tufekci, Mehmet; Soylak, Mustafa
A simple and rapid procedure based on the combination of carrier element free coprecipitation (CEFC) and flame atomic absorption spectrometric (FAAS) determinations has been developed for selective separation and preconcentration of Cu(II) ions in some environmental solid (Turkish and import coffee) and liquid (sea and stream waters) samples. In this method, acetohydrazide derivative was used as an organic coprecipitant without adding any carrier element for coprecipitation of Cu(II) ions. The preconcentration factor was found to be 50, the limit of detection (LOD) was 0.31 μgL -1, while the relative standard deviation (RSD) was found to be 1.6% for Cu(II) ions.
- MakaleAçık Erişim2012Optimization of a new cloud point extraction procedure for the selective determination of trace amounts of total iron in some environmental samples
Duran, Celal; Özdeş, Duygu; Çelenk Kaya, Elif; Kantekin, Halit; Bulut, Volkan Numan; Tüfekçi, Mehmet
A new, simple, and rapid cloud point extraction (CPE) procedure system, combined with flame atomic absorption spectrometry (FAAS), was developed for selective separation, preconcentration, and determination of trace amounts of total iron in some environmental samples. The complexing agent, N,N-(2,2 - (ethane-1,2-diylbis(oxy))bis(ethane-2,1-diyl))bis(2-chloroacetamide) (EDBOCA), is selective at pH 5.0 for only Fe(II) and Fe(III) ions in the presence of Cu(II), Pb(II), Cd(II), Mn(II), Co(II), Cr(III), Cr(VI), Ni(II), Zn(II), Al(III), Mo(VI), Pd(II), Pt(IV), Au(III), and V(V) ions. The procedure is based on the complexation of Fe(III) ions with EDBOCA reagent in the presence of Triton X-114 (TX-114) as a non-ionic surfactant. The optimum conditions for the CPE of Fe(III) ions were investigated with respect to several experimental parameters such as pH of the solution, TX-114 and EDBOCA concentrations, incubation time and temperature, and centrifugation rate and time. The detection limit for Fe(III) ions based on the 3 times the standard deviation of the blanks (N:10) was found to be 1.22 μg L ?1 , while the relative standard deviation (RSD) was 4.2%. Environment Canada TM-25.3 and CRM-SA-C Sandy Soil C, as certified reference materials, were used, and spike tests were applied to validate the method. The method was applied to some real environmental samples to evaluate their total iron levels.
- MakaleYalnız künye2012Adsorption of Phenol from Aqueous Solution on a Low-Cost Activated Carbon Produced from Tea Industry Waste: Equilibrium, Kinetic, and Thermodynamic Study
Gundogdu, Ali; Duran, Celal; Senturk, H. Basri; Soylak, Mustafa; Ozdes, Duygu; Serencam, Huseyin; Imamoglu, Mustafa
The ability of activated carbon which was produced by chemical activation using zinc chloride from tea industry wastes (TIWAC) to adsorb phenol molecules from aqueous solution was tested by equilibrium, kinetic, and thermodynamic parameters. Phenol adsorption on TIWAC took place with a high yield at pH values in the range 4 to 8. The optimum contact period was observed as 4.0 h and from the adsorption graphs plotted as a function of time; it was established that phenol adsorption on TIWAC conformed more to a pseudosecond-order kinetic model. Additionally, it was determined that the adsorption rate is controlled by intraparticle diffusion as well as film diffusion. It was established that phenol adsorption on TIWAC can be better defined by the Langmuir adsorption model and its adsorption capacity was 142.9 mg.g(-1) from the linear Langmuir equation. Temperature had an adverse effect on adsorption yield, and hence, the adsorption process was exothermic in our case. Moreover, increasing electrolyte concentration in the medium has a positive effect on adsorption yield. From the data obtained, it was concluded that the removal of phenol from aqueous solution by TIWAC produced from tea industry wastes with a very low cost took place with an extremely high performance.
- MakaleYalnız künye2011Preconcentration of Cd(II) and Cu(II) ions by coprecipitation without any carrier element in some food and water samples
Duran, Celal; Ozdes, Duygu; Sahin, Deniz; Bulut, Volkan Numan; Gundogdu, Ali; Soylak, Mustafa
A simple, rapid, sensitive and environmentally friendly separation and preconcentration procedure, based on the carrier element free coprecipitation (CEFC) of Cu(II) and Cd(II) ions by using an organic coprecipitant, 2-{[4-(4-fluorophenyl)-5-sulphanyl-4H-1,2,4-triazol-3-yl]methyl}-4-{[(4-fluorophenyl) methylene]amino}-5-(4-methylphenyl)-2,4-dihydro-3H-1,2,4-triazol-3-one (MEFMAT) was developed. The analyte ions were determined by flame atomic absorption spectrometric (FAAS) determinations. The optimum conditions for the coprecipitation process were investigated on several commonly tested experimental parameters such as pH of the solution, amount of MEFMAT, sample volume, standing time, centrifugation rate and time. The influences of some anions, cations and transition metals on the recoveries of analyte ions were also investigated, and no considerable interference was observed. The preconcentration factor was found to be 50. The detection limits for Cu(II) and Cd(II) ions based on the three times the standard deviation of the blanks (N:10) were found to be 1.49 and 0.45μgL-1, respectively. The relative standard deviations were found to be lower than 3.5% for both analyte ions. The method was validated by analyzing two certified reference materials (CRM-TMDW-500 Drinking Water and CRM-SA-C Sandy Soil C) and spike tests. The procedure was successfully applied to sea water and stream water as liquid samples and tobacco, hazelnut and black tea as solid samples.
- MakaleYalnız künye2011Kinetics and isotherm analysis of basic dyes adsorption onto almond shell (Prunus dulcis) as a low cost adsorbent
Duran, Celal; Ozdes, Duygu; Gundogdu, Ali; Senturk, Hasan Basri
The feasibility of using an agricultural byproduct, almond shell (Prunus dulcis), as an adsorbent in removal of basic dyes, namely, methylene blue (MB), methyl violet (MV), and toluidine blue O (TB), were evaluated in a batch adsorption process. The adsorption characteristics of MB, MV, and TB onto almond shell (AS) were investigated with respect to the changes in initial pH of dye solutions, contact time, initial dye concentration, and temperature. The dye adsorption equilibria were rapidly attained after 30 min of contact time. The adsorption kinetics were analyzed using pseudofirst-order, pseudosecond-order, Elovich, and intraparticle diffusion models and the adsorption data were well described by the pseudosecond-order model. The equilibrium adsorption data were interpreted in terms of the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich (D-R) isotherm models. The monolayer adsorption capacity of AS was found to be 51.02 mg·g-1 for MB, 76.34 mg·g-1 for MV, and 72.99 mg·g-1 for TB by using the Langmuir model equation. The thermodynamic parameters proved that the present adsorption process was feasible, spontaneous and endothermic in nature in the temperature range of (5 to 40) °C.