Sürdürülebilir Kalkınma Amaçları
Yayınlar
- MakaleYalnız künye2018Automated Model Updating of Historical Masonry Structures Based on Ambient Vibration Measurements
Altunisik, Ahmet Can; Okur, Fatih Yesevi; Genç, Ali Fuat; Günaydin, Murat; Adanur, Suleyman
Finite-element (FE) model updating is a very effective procedure for determining the uncertainty parameters in a structural model and minimize differences between experimentally and analytically identified dynamic characteristics. This procedure can be practiced with manual and global/local automatic model updating procedures. Automatic model updating is very popular because of its applicability to all kinds of engineering structures to minimize differences, and its damage localization and structural health monitoring. This paper considers a historical masonry bastion to obtain its dynamic characteristics numerically with the finite-element method and experimentally with ambient vibration tests (AVTs). Sensitivity analyses for the uncertainty parameters and manual and automated model updating to minimize differences are also performed. A castle bastion located in Trabzon, Turkey is selected as an application. The FE model of structure is developed in commercial software. The first three natural frequencies are obtained between 5 and 10Hz, and AVTs are performed under natural excitation using enhanced frequency domain decomposition (EFDD) and subspace structural identification (SSI) techniques. The first three natural frequencies are obtained between 4 and 7Hz. The comparison of analytically and experimentally identified dynamic characteristics shows a close agreement between mode shapes, but 26% difference in natural frequencies. To minimize the difference, the FE model of the bastion is updated using manual and global/local automated updating, changing its material properties of Young's modulus and material density. The maximum differences are reduced from 27 to 3% with manual updating, and to 0.02% with automated model updating.
- MakaleYalnız künye2018EFFECTS OF STRAND CONFIGURATION ON PRE-TENSIONED I-GIRDERS
Atmaca, Barbaros; Ates, Sevket; Günaydin, Murat; Altunisik, Ahmet Can
The purpose of this paper is to examine the effect of strand configuration on the behavior of precast, pre-tensioned concrete I-girders by considering design load components for highway bridges as dead loads and equivalent lane loads. Under these loads, bridge girder's bottom flange is exposed to tensile stresses. To minimize or eliminate the tensile stresses, compressive stresses are induced in pre-stressed concrete with strands. Determination of strand configuration is important as well as number of strands because it affects stress distribution and displacement of bridge girders. One of the typical precast I-girder with 90 cm height is considered in this study. To determine strand configuration effects, eighteen I-girders with the same cross-section, effective span length and material properties but different strand configuration are selected as an application. Equal prestressing force is applied all strands simultaneously. Three dimensional finite element (FE) models of girder are constituted using ANSYS software. Result of beam theory is used to verify the modeling techniques. At the end of the study, numerically identified stress distribution and displacement for I-girders compared with each other. It is seen that proper strand configuration is effective to reducing stresses and displacements of pre-stressed I-girder.
- MakaleYalnız künye2016Retrofitting Effect on the Dynamic Properties of Model-Arch Dam with and without Reservoir Water Using Ambient-Vibration Test Methods
Altunisik, Ahmet Can; Günaydin, Murat; Sevim, Baris; Bayraktar, Alemdar; Adanur, Suleyman
Continuous health monitoring and regular condition assessment is of vital importance for engineering structures in general and especially for arch dams. These structures can be exposed to many different loads such as earthquake, blast, wind, ice, and water pressure, which may cause deterioration and loss of structural integrity. Such development may have severe economic consequence and, more importantly, may present a serious risk to public safety. Therefore, the structural behavior of arch dams must be monitored at regular intervals during their service life, although the overall failure rate of these dams is around 1%. Experimental measurements by ambient vibration test methods are among the most commonly preferred inspection techniques for the evaluation of structural performance and safety. The aim of this research is to examine the retrofitting effect on the dynamic properties of a damaged arch dam model, with and without reservoir water, after retrofitting with high-strength structural repair mortar and carbon fiber reinforced polymer composite material. To this end, an arch dam-reservoir-foundation model was built. In the study, ambient vibration tests were carried out for three test-cases to determine changes in dynamic properties, such as natural frequency, mode shape, and damping ratio before and after retrofitting. The three cases were (1)a severely damaged dam with full reservoir (Case-A), (2)a repaired dam with full reservoir (Case-B), and (3)a strengthened dam with full reservoir (Case-C). In addition, all the measurement tests were repeated with an empty reservoir to extract the effect of water. Data for the ambient vibration tests were gathered from the dam body during vibrations by natural excitations. These excitations were provided through small impacts, and the response signals were measured by sensitivity accelerometers placed at the crest points. To obtain the experimental dynamic properties, the enhanced frequency domain decomposition method in the frequency domain was used. Comparisons of experimentally identified dynamic properties for the damaged and the retrofitted dam showed that the retrofitting application affected the structural behavior of the arch dam considerably. It was very effective in restoring the structure's original dynamic properties.
- MakaleYalnız künye2016Dynamic Characteristics of an Arch Dam Model before and after Strengthening with Consideration of Reservoir Water
Altunisik, Ahmet Can; Günaydin, Murat; Sevim, Baris; Bayraktar, Alemdar; Adanur, Suleyman
This technical note presents an investigation about the changing of dynamic characteristics of an arch dam model before and after strengthening considering reservoir water. To this end, an arch dam-reservoir-foundation model has been constructed in the laboratory. Ambient vibration tests have been performed on the damaged and strengthened arch dam models for empty and full reservoir to determine the effect of water on the dynamics characteristics. Enhanced frequency domain decomposition method has been used to extract the dynamic characteristics. Finally, the dynamic characteristics obtained from the damaged and strengthened dam models have been compared to with each other. Also, the natural frequencies for damaged and strengthened models are compared to detect the effect of strengthening application on the frequencies. Results indicate that the natural frequencies and damping ratios are changed with the full reservoir. However, mode shapes are not changed. Results also show that the natural frequencies of damaged dam considerably increase after strengthening applications.
- MakaleYalnız künye2012Construction stage analysis of fatih sultan mehmet suspension bridge
Günaydin, Murat; Adanur, Suleyman; Altunisik, Ahmet Can; Sevim, Baris
In this study, it is aim to perform the construction stage analysis of suspension bridges using time dependent material properties. Fatih Sultan Mehmet Suspension Bridge connecting the Europe and Asia in Istanbul is selected as an example. Finite element models of the bridge are modelled using SAP2000 program considering project drawing. Geometric nonlinearities are taken into consideration in the analysis using P-Delta large displacement criterion. The time dependent material strength variations and geometric variations are included in the analysis. Because of the fact that the bridge has steel structural system, only prestressing steel relaxation is considered as time dependent material properties. The structural behaviour of the bridge at different construction stages has been examined. Two different finite element analyses with and without construction stages are carried out and results are compared with each other. As analyses result, variation of the displacement and internal forces such as bending moment, axial forces and shear forces for bridge deck and towers are given with detail. It is seen that construction stage analysis has remarkable effect on the structural behaviour of the bridge.
- MakaleYalnız künye2012Estimation of Elasticity Modulus of a Prototype Arch Dam Using Experimental Methods
Sevim, Baris; Altunisik, Ahmet Can; Bayraktar, Alemdar; Akköse, Mehmet; Adanur, Suleyman
Using experimental methods, this study presents the estimation of the dynamic and static ( secant) elasticity modules of a prototype arch dam. These experimental methods are ambient vibration tests, uniaxial compression tests, and ultrasonic velocity tests. Implementation of the methods on a prototypical arch dam-reservoir-foundation model of the dam, constructed under laboratory conditions, allows estimation of the elasticity modules. Random impact loads excite the arch dam during ambient vibration testing, which creates response signals for measurement. Commercially available software transfers the signals, and processing those signals allows estimation of the experimental natural frequencies of the arch dam. Analysis of a three-dimensional (3D) finite element model (FEM) of the arch dam determines natural frequencies. The estimation of the elasticity modules of the arch dam arises from a comparison of the experimental and analytical frequencies. The uniaxial compression tests use several specimens of the fresh and hardened concrete of the prototype model, and those tests provide the compressive strengths and stress-strain relationships. The ultrasonic velocity tests apply several velocity measurements to the arch dam and foundation, resulting in estimation of the elasticity modulus from empirical equations related to concrete mix design, compressive strength, and velocity values. This study discusses the difficulties of the determination of the elasticity modulus and suggests that ambient vibration testing and the finite element method are useful for overcoming these difficulties. DOI: 10.1061/(ASCE)MT.1943-5533.0000361. (C) 2012 American Society of Civil Engineers.
- MakaleYalnız künye2011Finite element model calibration effects on the earthquake response of masonry arch bridges
Sevim, Baris; Bayraktar, Alemdar; Altunisik, Ahmet Can; Atamtürktür, Sezer; Birinci, Fatma
The focus of this paper is to illustrate the importance of model calibration and in situ vibration testing by comparing the finite element model predictions of the earthquake response of the two historical arch bridges, Osmanli and Senyuva, before and after model calibration. The three-dimensional finite element models of these two arch bridges, built in the ANSYS finite element program, are used to predict bridge dynamic characteristics, such as natural frequencies and mode shapes. Following the analytical study, ambient vibration tests were conducted to experimentally obtain dynamic characteristics of these two bridges. During ambient vibration tests, accelerometers were placed at several points on the bridge to collect the vibration response due to natural and operational excitation sources. Enhanced frequency domain decomposition and stochastic subspace identification techniques were used to extract the experimental natural frequencies, mode shapes and damping ratios. Finite element models of the two arch bridges were adjusted such that the model predictions reproduce the ambient vibration test results with increased fidelity. The behavior of the masonry arch bridges under earthquake excitation recorded during the Erzincan Earthquake in 1992 is simulated by both the initial and adjusted finite element models. The findings of this study emphasize the importance of model calibration and ambient vibration testing. (C) 2010 Elsevier B.V. All rights reserved.
- MakaleYalnız künye2011Finite element model updating effects on nonlinear seismic response of arch dam-reservoir-foundation systems
Bayraktar, Alemdar; Sevim, Baris; Altunisik, Ahmet Can
This paper investigates the effects of finite element model updating on nonlinear seismic response of arch dam-reservoir-foundation systems. The highest arch dam in Turkey named Berke is selected for the numerical and experimental applications. Firstly, 3D finite element model of Berke Dam was constituted using an ANSYS software. In the analytical modeling, arch dam-reservoir-foundation interaction is represented by Lagrangian approach. Then ambient vibration tests were conducted to dam for four days, and experimental dynamic characteristics were estimated using an Enhanced Frequency Domain Decomposition technique. Experimental characteristics are compared with those of analytical obtained by the linear finite element analysis of the coupled system. Good agreement between mode shapes is observed during this comparison, though natural frequencies disagree by 15-20%. The linear finite element model of Berke Dam was updated by adjusting the material properties of the dam and foundation. By introducing the Drucker-Prager damage criterion, the updated linear finite element model was extended into an onlinear model. Nonlinear seismic behavior of Berke Dam was determined considering the acceleration record of Adana-Ceyhan, Turkey, earthquake in 1998 that occurred near the arch dam region. It is highlighted that the finite element model updating provides a significant influence on the nonlinear seismic response of arch dams. (C) 2010 Elsevier B.V. All rights reserved.