Sürdürülebilir Kalkınma Amaçları
Yayınlar
- MakaleAçık Erişim2025Flexural Behavior and Sustainability of Dual-Waste Fiber-Reinforced Concrete Designed for Pavement Applications
Seferoğlu, Mehmet Tevfik; Aksüt, Yavuz Selim; Seferoğlu, Ayşegül Güneş
This study evaluates the mechanical performance and sustainability potential of fiber-reinforced concrete incorporating mine tailings as the fine aggregate and waste tire wire as the reinforcing fiber. The concrete mixtures contained 0.2%, 0.4%, and 0.6% waste tire wire with the natural fine aggregate replaced entirely with Pb-Zn-Cu tailings. The mixtures were tested for porosity, water absorption, compressive strength, splitting tensile strength, flexural strength, toughness, fracture energy, and ductility to assess their mechanical performance and durability. The mine tailings improved the microstructure and reduced water absorption, particularly with tire wire. Using waste tire wire improved the compressive, tensile, and flexural performance; in particular, W-6 showed a 18.2% rise in compressive strength and a more than twofold increase in flexural strength relative to the control mix. The flexural toughness and fracture energy rose by up to 161%, while the ductility peaked at a fiber content of 0.2%. These gains were attributed to fiber crack-bridging and post-cracking energy absorption. The dual-waste system also reduced porosity, improved durability, and demonstrated strong potential for rigid pavement applications such as highways, industrial yards, and airport runways that require high fatigue resistance and a long service life. Beyond technical performance, this approach offers a sustainable solution that lowers maintenance, reduces life-cycle costs, and aligns with circular economy principles.
- MakaleYayıncıda açık erişim2025Assessing the reliability of the lightweight deflectometer test for compaction control in highway subbase layers through SPSS analysis
Seferoğlu, Mehmet Tevfik; Seferoğlu, Ayşegül Güneş; Akpınar, Muhammet Vefa; Iribagiza, Divine
The condition of the highway base/subbase layers is critical for the durability and performance of the road pavement. Compaction control plays an important role in determining the ability of these layers to support traffic loads, their strength and stability. Various methods are used to evaluate the compaction rate of subbase layers; such as nuclear density gauge (NDG) and sand cone. These methods also have their own limitations and difficulties. While the NDG test is used to determine the compaction percentages, the lightweight deflectometer (LWD) test is used as a relatively more practical, portable and non-destructive method to measure the surface stiffness modulus (Emod). In this study, the possibility of using the surface stiffness modulus obtained by the LWD test in the subbase layer instead of each other is investigated by establishing a correlation between the compaction percentages determined by the NDG test. To investigate how well the LWD results are in line with established methods, only correlation and regression analysis of SPSS software are focused on. Correlation analysis helped us assess the strength and direction of the relationships between LWD modulus values and compaction percentages, while regression analysis provided insights into the predictive capability of LWD in estimating compaction outcomes. These methods helped evaluate the reliability and accuracy of LWD as a compaction control tool, providing a deeper understanding of the role of LWD in highway subbase layer assessment.
- MakaleAçık Erişim2023Investigation of the structural damage caused by blasting activities in tunnels to surrounding buildings: The case of Gümüşhane belt highway; [Tünellerde patlatma faaliyetlerinin çevre binalara verdiği yapısal hasarın incelenmesi: Gümüşhane çevre yolu örneği]
Seferoğlu, Mehmet Tevfik; Seferoğlu, Ayşegül Güneş; Akaryali, Enver
Tunnels are road transport structures that reduce traffic and expropriation problems, noise, and possible damage to animals and plants, and provide safer, more comfortable, and faster transportation for vehicles compared to highways. However, some environmental problems occur during tunnel construction. These problems such as vibration, noise, rock throwing, etc. caused by the blasting process used during tunnel excavation on buildings and people should be well investigated. In this study, two buildings located close to the exit and entrance of two tunnels (T2 and T3 tunnels) on the Gümüşhane belt road were chosen to investigate. Firstly, the existing damages in the first building, which is 7 m away from the T2 tunnel exit, and the second building, which is 60 m away from the T3 tunnel entrance, were analyzed by considering criteria such as the geological and ground condition of the land and the building materials used during the construction of those building. In addition, the negative effects on the buildings were evaluated by calculating the vibrations after the blasting process in the tunnel with the help of various empirical formulas. Investigation on site showed that building 1 was built of masonry and building 2 was built of reinforced concrete, and that deep cracks had formed in the bearing systems of both buildings, spills occurred in the walls, and fractures in the windows. Also, calculations with empirical formulas showed that the vibration rates caused by blasting process in the 1st and 2nd buildings were as 385.68 mm/sec and 6.91 mm/sec, respectively, and these vibration values were above the standard values. The data obtained through examination on-site and empirical approaches show that it would be dangerous for people to be resident in both buildings.
- MakaleYayıncıda açık erişim2019Investigating the mechanical behavior of reclaimed asphalt pavement (RAP) bases in large scale test box
Seferoğlu, Ayşegül Güneş; Seferoğlu, Mehmet Tevfik; Akpinar, Muhammet Vefa
The objective of this research was to assess the elastic deformations and permanent strains of reclaimed asphalt pavement (RAP) material as a base layer when it is treated or untreated with pozzolanic cement under cyclic loads. A large-scale cyclic plate loading testing (CPLT) device was developed for studying the mechanical characteristics of pavement base layer. The laboratory test results indicated that when the RAP percentage of the mixtures increased, elastic deformations and permanent strains increased, but the opposite was true when the cement percentage increased. It was concluded that 100% RAP material can be used in base layers with 3% pozzolanic cement. The obtained deformation values and strain rates can be used as reasonable default design input values by pavement designers when using RAP as a substitute for natural aggregate base layers.
- MakaleYalnız künye2018Experimental study on cement-treated and untreated RAP blended bases: Cyclic plate loading test
Seferoğlu, Ayşegül Güneş; Seferoğlu, Mehmet Tevfik; Akpinar, Muhammet Vefa
The asphalt surrounding the reclaimed asphalt pavement (RAP) aggregates decrease the performance characteristics of road layers. RAP material increases the permanent deformation potential of road layers under the traffic load. In this study, the performances of RAP-VA (Virgin aggregate) mixtures was tested using cyclic plate loading test by adding pozzolanic cement into mixtures in order to use RAP material at the rate of 100% and to minimize the permanent deformation in plant-mix base courses (PBC). The permanent surface deformations of base course were measured at different points throughout 100 loading cycles and all of the measurements were compared to that of base course prepared from 100% VA. The effect of RAP/cement rate of mixtures on the permanent deformations was examined and it was determined that the increase in RAP rate increased the permanent deformations but cement significantly decreased it. Moreover, considering the material costs of mixtures, the cost analysis was performed and the profit margins that using RAP and cement offers to constructors were computed.