Gül, Fatih

Resistive random access memories (RRAMs) are favorable contenders in the race towards future technologies. Moreover, the desirable properties of memristor-based RRAM devices make them very good competitors in this field. The sneak paths problem poses one of the main difficulties in the construction of crossbar memory devices. This problem can be effectively suppressed by applying the 1diode-1resistor (1D1R) design structure. The Schottky diode has many advantages compared to the PN junction diode. The low-power (∼1 µW) ZnO active-layered thin-film (60 nm thick) one Schottky diode-one memristor device fabricated in this study included a top Ag electrode and a bottom Al electrode. The material makeup of the device was confirmed via energy dispersive X-ray spectroscopy (EDAX). The memristive and Schottky diode characteristics of the Ag/ZnO/Al device were resolved by measuring the time-dependent voltage/current. The characteristic pinched hysteresis memristive loops were observed at the first quadrant of the current-voltage plane, whereas the diode curves were seen at the third quadrant. Using the current-voltage curves, the height of the Schottky barrier, ideality factor and threshold voltage of the Schottky diode were found to be 0.68 eV, 3.75 and 0.49 V, respectively. After physical implementation and characterization of the one diode-one memristor device, its anti-crosstalk characteristics were investigated. Taking into account the 10% read margin, the maximum crossbar size was found to be 87.

Manay, Eyuphan; Akyürek, Eda Feyza; Sahin, Bayram

Present study aims to investigate the effects of the presence of nano sized TiO2 particles in the base fluid on entropy generation rate in a microchannel heat sink. Pure water was chosen as base fluid, and TiO2 particles were suspended into the pure water in five different particle volume fractions of 0.25%, 0.5%, 1.0%, 1.5% and 2.0%. Under laminar, steady state flow and constant heat flux boundary conditions, thermal, frictional, total entropy generation rates and entropy generation number ratios of nanofluids were experimentally analyzed in microchannel flow for different channel heights of 200 mm, 300 mm, 400 mm and 500 mm. It was observed that frictional and total entropy generation rates increased as thermal entropy generation rate were decreasing with an increase in particle volume fraction. In microchannel flows, thermal entropy generation could be neglected due to its too low rate smaller than 1.10e-07 in total entropy generation. Higher channel heights caused higher thermal entropy generation rates, and increasing channel height yielded an increase from 30% to 52% in thermal entropy generation. When channel height decreased, an increase of 66%-98% in frictional entropy generation was obtained. Adding TiO2 nanoparticles into the base fluid caused thermal entropy generation to decrease about 1.8%-32.4%, frictional entropy generation to increase about 3.3%-21.6%. (C) 2018 The Authors. Published by Elsevier B.V.

Akyürek, Eda Feyza; Geliş, Kadir; Şahin, Bayram; Manay, Eyüphan

Nanofluids are a novel class of heat transfer suspensions of metallic or nonmetallic nanopowders with a size of less than 100 nm in base fluids and they can increase heat transfer potential of the base fluids in various applications. In the last decade, nanofluids have become an intensive research topic because of their improved thermal properties and possible heat transfer applications. For comparison, an experiment using water as the working fluid in the heat exchanger without wire coils was also performed. Turbulent forced convection heat transfer and pressure drop characteristics of Al2O3-water nanofluids in a concentric tube heat exchanger with and without wire coil turbulators were experimentally investigated in this research. Experiments effected particle volume concentrations of 0.4–0.8 to 1.2–1.6 vol% in the Reynolds number range from 4000 to 20,000. Two turbulators with the pitches of 25 mm and 39 mm were used. The average Nusselt number increased with increasing the Reynolds number and particle concentrations. Moreover, the pressure drop of the Al2O3-water nanofluid showed nearly equal to that of pure water at the same Reynolds number range. As a result, nanofluids with lower particle concentrations did not show an important influence on pressure drop change. Nonetheless, when the wire coils used in the heat exchanger, it increased pressure drop as well as the heat transfer coefficient.