Sürdürülebilir Kalkınma Amaçları

• 2
• 1

• MakaleYalnız künye2024/r/gumushane/14291
  Hysteretic behaviour of square-hollow-section T- and X-joints with in-plane bending moment

  Ozyurt, E.; Gunaydin, M.

  This study examined the hysteretic behaviour of Square Hollow Section (SHS) T- and X-joints subjected to cyclic in-plane bending moments. A nonlinear finite element software, Abaqus, was used to investigate SHS T- and X-joint seismic performance. Prior to the parametric study, the numerical model was validated based on the available test results in the literature. A comprehensive parametric study employed validated finite element models to evaluate the influence of critical geometric parameters, including the brace-to-chord width ratio (β) and the chord width-to-thickness ratio (γ). The results of the finite element analyses regarding ductility, flexural strength, and energy dissipation behaviour of SHS T- and X-joints under quasi-static cyclic in-plane bending were evaluated. Based on the hysteretic curves, increasing β generally leaded to higher initial stiffness and moment capacity in SHS joints, considerably reducing joint rotation. Conversely, the joints with larger γ exhibited reduced initial stiffness and moment capacity. Besides, the Eurocode 3 EN1993-1-8 predictions for the ultimate flexural strength of the joints are found to be conservative compared to finite element results. The results also revealed that the SHS T- and X-joints showed satisfactory ductility levels under in-plane bending load. It was observed that the SHS T- and X-joints with high β and low γ are advantageous for absorbing energy under seismic loads. These findings offered valuable insights for the seismic-resistant design of structures incorporating SHS joints, aiding in selecting optimal configurations based on specific performance requirements.

  • 
  İncele
• MakaleYalnız künye2024/r/gumushane/11418
  Axial resistance of elliptical hollow section K-joints made of high strength steel

  Ozyurt, E.

  The present study examined the axial resistance of welded elliptical hollow section (EHS) K-joints made of high-strength steel (HSS). The axial resistance of EHS K-joints was affected by a range of factors, including the geometrical parameters, orientations, chord pre-stress levels, and the mechanical properties of the high-strength steel grades. This research aimed to investigate the performance of welded EHS K-joints made of HSS under axial loading conditions with or without chord pre-stresses. Finite element analysis was employed for numerical simulations to analyze the nonlinear behaviour of EHS K-joints with HSS. It was observed from the numerical results that the orientation types significantly affected normalised resistance ratios. In contrast, β, γ, θ, and chord pre-stress levels had minimal impact, as comparisons were based on normalised resistance ratios. However, non-dimensional geometric parameters and chord pre-stress levels notably influenced the axial joint resistance of the HSS K-joints. As for predicting the axial resistances of EHS K-joints with HSS, the numerical results indicated that the existing reduction factor might be unsafe for the equivalent RHS method to be applied in the current design guides. Therefore, a new reduction factor was proposed for EHS K-joints with HSS that yield unsafe results.

  İncele
• MakaleYalnız künye2011/r/gumushane/15390
  Experimental and analytical system identification of Eynel arch type steel highway bridge

  Altunişik, Ahmet Can; Bayraktar, Alemdar; Sevim, Bariş; Özdemir, Hasan

  This paper describes a full scale arch type steel highway bridges, its finite element modelling and Operational Modal Analysis. Eynel Highway Bridge which has arch type structural system with a total length of 336 m and located in the AyvacIk county of Samsun, Turkey is selected as a case study. The bridge connects the villages which are separated with Suat Uǧurlu Dam Lake. The three dimensional finite element model is constructed using project drawings and an analytical modal analysis is then performed to generate natural frequencies and mode shapes in the three-orthogonal directions. The ambient vibration tests on the bridge deck under natural excitation such as traffic, human walking and wind loads are conducted using Operational Modal Analysis. Sensitive seismic accelerometers are used to collect signals obtained from the experimental tests. To obtain experimental dynamic characteristics, two output-only system identification methods are employed namely, Enhanced Frequency Domain Decomposition method in the frequency domain and Stochastic Subspace Identification method in time domain. The correlation between the finite element model and experimental results is studied. Good agreement is found between dynamic characteristics in the all measurement test setups performed on the bridge deck. It is demonstrated that the ambient vibration measurements using Enhanced Frequency Domain Decomposition and Stochastic Subspace Identification methods are enough to identify the most significant modes of steel highway bridges. It is seen that there are some differences between analytical and experimental natural frequencies and experimental natural frequencies are generally bigger than the others.

  • 
  • 
  İncele